|
|
|
|
DataqSdk Control > Log File |
|
|
|
|
|
DataqSdk Control > Log File |
|
A log file (DATAQSDK.LOG) may be created in the directory from which your program runs every time you run the DataqSDK control. This tool helps DATAQ Technical Support to debug your program if errors occur and you cannot figure out the problem.
To enable creation of this log file add the line "debug=1" to the [Global] section of the c:\Windows\TPDATAQ.INI file.
Note: The log file is cleared each time the DataqSDK control is loaded. In VB when an error occurs do not stop the program - the program must still be running to access the log file (i.e., stay in "debug" mode). For help with your program make sure you copy and email the log file before closing your application.
By using this log file Technical Support can significantly reduce response time to your problem.
Examine the following for a typical log file format:
15:37:33 Constructor
15:37:33 DoPropExchange
15:37:33 ADChannelCount 1
15:37:33 SampleRate 1000.000000
15:37:33 MaxSampleRate 0.000000
15:37:33 EventPoint 0
15:37:33 TrigMode 0
15:37:33 TrigScnChnIdx 0
15:37:33 TrigHysterisisIdx 0
15:37:33 TrigLevel 0
15:37:33 TrigPostLength 0
15:37:33 TrigPreLength 0
15:37:33 TrigSlope 0
15:37:34 SetADChannelCount 4
15:37:34 SetMaxBurstRate= 50000.000000
15:37:34 SetADChannelCount 100.000000
15:37:34 SetEventPoint 20
15:37:34 ADChannelList
15:37:34 [0]= 0
15:37:34 [1]= 1
15:37:34 [2]= 2
15:37:34 [3]= 3
15:37:34 [4]= 4
15:37:34 [5]= 5
15:37:34 [6]= 6
15:37:34 [7]= 7
15:37:34 [8]= 8
15:37:34 [9]= 9
15:37:34 [10]= 10
15:37:34 [11]= 11
15:37:34 [12]= 12
15:37:34 [13]= 13
15:37:34 [14]= 14
15:37:34 [15]= 15
15:37:34 [16]= 16
15:37:34 [17]= 17
15:37:34 [18]= 18
15:37:34 [19]= 19
15:37:34 [20]= 20
15:37:34 [21]= 21
15:37:34 [22]= 22
15:37:34 [23]= 23
15:37:34 [24]= 24
15:37:34 [25]= 25
15:37:34 [26]= 26
15:37:34 [27]= 27
15:37:34 [28]= 28
15:37:34 [29]= 29
15:37:34 [30]= 30
15:37:34 [31]= 31
15:37:34 [32]= 0
15:37:34 ADGainList
15:37:34 [0]= 0
15:37:34 [1]= 0
15:37:34 [2]= 0
15:37:34 [3]= 0
15:37:34 [4]= 0
15:37:34 [5]= 0
15:37:34 [6]= 0
15:37:34 [7]= 0
15:37:34 [8]= 0
15:37:34 [9]= 0
15:37:34 [10]= 0
15:37:34 [11]= 0
15:37:34 [12]= 0
15:37:34 [13]= 0
15:37:34 [14]= 0
15:37:34 [15]= 0
15:37:34 [16]= 0
15:37:34 [17]= 0
15:37:34 [18]= 0
15:37:34 [19]= 0
15:37:34 [20]= 0
15:37:34 [21]= 0
15:37:34 [22]= 0
15:37:34 [23]= 0
15:37:34 [24]= 0
15:37:34 [25]= 0
15:37:34 [26]= 0
15:37:34 [27]= 0
15:37:34 [28]= 0
15:37:34 [29]= 0
15:37:34 [30]= 0
15:37:34 [31]= 0
15:37:34 [32]= 0
15:37:34 ADDiffList
15:37:34 Link2DLL
15:37:34 di809nt.dll
15:37:34 Start
15:37:34 OnCreate
15:37:34 ChangeBoard
15:37:34 DI_CLOSE
15:37:34 DI_OPEN_URL
15:37:34 192.168.1.111
15:37:34 DI_OPEN ok, entering DI_INFO
15:37:34 DI_INFO
15:37:34 DeviceName 720
15:37:34 dDspFrq= 16000000.000000
15:37:34 Starting GetBCInfo
15:37:34 Non BC Priority
15:37:34 Number of Channel: 4
15:37:34 Samplerate: 100
15:37:34 MinBurstCount: 320
15:37:34 Loop: 0
15:37:34 Iteration: 1
15:37:34 Loop: 1
15:37:34 Iteration: 2
15:37:34 GetBCInfo: 320 124
15:37:34 Actual Rate= 100.000000
15:37:34 DI_MODE
15:37:34 DI_BURST_RATE
15:37:34 DI_BUFFER_ALLOC
15:37:34 DI_LIST_LENGTH
15:37:34 Bipolar 0 0
15:37:34 Bipolar 1 1
15:37:34 Bipolar 2 2
15:37:34 Bipolar 3 3
15:37:34 Next: DI_START_SCAN
15:37:34 NewData 48
15:37:34 GetData
15:37:34 SetDigitalOutput 32767
15:37:35 NewData 80
15:37:35 GetData
15:37:35 SetDigitalOutput 0
15:37:35 NewData 80
15:37:35 GetData
15:37:35 SetDigitalOutput 32767
15:37:35 NewData 80
15:37:35 GetData
15:37:35 SetDigitalOutput 0
15:37:35 NewData 80
15:37:35 GetData
15:37:35 SetDigitalOutput 32767
15:37:35 Stop
15:37:38 Disconnect device driver
15:37:38 Done Destructor
